Services
 

Please fill out all the information on the Bid Specification Sheet. When you are done, click on the "Submit Request" button near the bottom of the page. We will get back to you with your quote as soon as we review the information you provided. Thank you for allowing us to quote your project.

Job Specification Sheet:
PM#
Date: Date Month Year
ProMoldGauer, Inc.  
Contact Name:
Phone: 330-633-3532 ext.
Fax: 330-633-5017
E-mail:
   
Customer:
Contact Name:
Phone:
Cell:
Fax:
E-mail:
Address:
P.O.#:
   
Part Data:  
Part Name:
Part Number:
  Customer to provide complete part CAD data.
  Customer to approve gate location on part.
Resin Supplier:
Resin Filler:
Molding Resin:
Shrink Rate:
Vent Depth:
Vent Geometry:
   
Mold Data:  
Number of Cavities:
Mold Cat. Number:
Mold Series: A B X
Other:
  O = R =
  D = C =
  S = M =
Mold Steel Type: #1 #2 #3
Other:
Cavity Insert Pocket Type: Blind Through

 

Mold Design Specifications:    
Supplied by Customer Use SPI Standards
Supplied by PMG Use NTMA Standards
Show tie bars on mold layout Customer to approve Gate Location
Customer to approve mold design Electric Box for Heater Control required
Special Actions:
Reverse Injection Buried Core Pull
Gas Assist Spring Loaded Ejector
Rack Driven Tri-Plate Stripper Ring Ejector
Pull Rod Drive Tri-Plate Latch Driven Ejector
Latch Driven Tri-Plate Accelerated Ejector
2 Stage Injection Engraving Inserts
"Bermer" Ejector Return Cycle Counter
Stripper Plate Ejector Mechanical Core Pull
Guided Ejectors Hydraulic Core Pull
Parting Line Locators Spring Load Core Pull
Air Blast Assist Rack Drive Unscrew
Ejector Pull Back Spline Drive Unscrew
Chain Pull Ejector Motor Drive Unscrew
2 Stage Ejector Early Ejector Return
Inject/Eject Air Assisted Ejector
Stack Molding Front Ejection
Front Half Cam Action Date Inserts
Internal Lifters Recycle Medallion
       
Special Heating/Cooling:    
Water line tap size
  Metric Inch    
Blade Baffles Hot Oil Fittings #
     
Spiral Cooling Cores Heater Cartridges
Thermal Pins Recess All Fittings
Gas Charged Cores In Cavity & Core
Bubbler Tubes In Slides
Logic Seal Cooling In Mold Plates
Cascade Junction In Retainer Plates
Rotating Union Tubular Heaters
Jiffy Plugs # Other
     
       
Ejector Information:    
Pins Strippers
Sleeves Air Blasts
Blades Other
Lifters    
       
Gating Information:    
Pin Point (3 Plate) Multi-Tip (Hot Runner)
Pin Point Tip (1) Fan (Cold Runner)
Hot Runner Diaphragm (Cold Runner)
Valve Gate (Hydraulic) Edge Gate (Hot Runner)
Chisel (Cold Runner) Edge Gate (Cold Runner)
Banana (Cold Runner) Sub-Gate (Cold Runner)
Valve Gate (Pneumatic) Tab (Cold Runner)
Multi-Tip (3 Plate) Diaphragm (Hot Runner)


Runner Type:
Hot Runner Supplier:
  Low Voltage High Voltage
   
Cavity & Core:  
Cavity:  
Cavity Mat'l:
Heat Treat:
Plating:
Surface Finish:
Texture:
Engraving:
Gate Insert:  
Gate Mat'l:
Heat Treat:
Plating:
Surface Finish:
Core:  
Core Mat'l:
Heat Treat:
Plating:
Surface Finish:
Texture:
Engraving:
Cavity I. D. #:
Stripper:  
Striper Mat'l:
Heat Treat:
Plating:
Surface Finish:
Texture:
Sub-Insert:  
Sub Insert Mat'l:
Heat Treat:
Plating:
Surface Finish:
Texture:
Slide:  
Slide Mat'l:
Heat Treat:
Plating:
Surface Finish:
Texture:
Engraving:
Lifter:  
Lifter Mat'l:
Heat Treat:
Plating:
Surface Finish:
Rotating Core:  
Material:
Heat Treat:
Plating:
Surface Finish:
   
Molding Machine Data:  
Press Manufacturer:
Clamp Tonnage:
K.O. Pattern:
SPI Standard:
Pull Back Thread Size:
Ejector Stroke:
Maximum Ejector Stroke:
Tie Bar Diameter:
Tie Bar Spacing:

(H) 
(V)

 
Minimum Mold Height:
Maximum Mold Height:
Core Pull Sequence Equipped - Style:
Integrated Hot Runner Controls: Low Voltage High Voltage
Preferred CAD file type:
Notes:
 



If you have any questions please contact:

Sales and Purchasing Manager
Chris Smith
330-633-3532 - ext. 31
chris.s@promoldgauer.com

or

Quoting and Purchasing
Jack Burns
330-633-3532 - ext. 32
jack.b@promoldgauer.com
 
 
 
Image